The water contains various ions, high hardness and high calcium, and other high hardness water can form fouling and scaling on the reverse osmosis membrane. Jiaming Water Treatment Technology's high hardness and high calcium water reverse osmosis scale inhibitor can be prepared according to technical requirements, providing free water quality testing and analysis, free trial use of high hardness and high calcium water reverse osmosis scale inhibitor product samples, free on-site inspection of large equipment, and comprehensive technical support and services.

Jiaming High Hard Water Reverse Osmosis Scale Inhibitor is a scale inhibitor specifically designed for reverse osmosis (RO) systems, nanofiltration (NF) and ultrafiltration (UF) systems. It can prevent membrane fouling, improve water production and quality, and reduce operating costs.

The main features are as follows:

① Effectively control inorganic compound scaling in a large concentration range

② Not condensed with iron aluminum oxides and silicon compounds to form insoluble substances

③ It can effectively inhibit the polymerization and deposition of silicon, and the concentration of SiO2 on the concentrated water side can reach 290

④ Can be used for reverse osmosis CA and TFC membranes, nanofiltration membranes, and ultrafiltration membranes

⑤ Excellent solubility and stability

⑥ The pH value of feedwater is valid within the range of 5-10

Jiaming High hardness and high calcium water reverse osmosis scale inhibitor can be prepared according to technical requirements. The commonly used Jiaming Water Treatment Technology's high hardness water reverse osmosis scale inhibitor BT0110 product introduction is as follows.

Jiaming High Hard Water Reverse Osmosis Scale Inhibitor BT0110 is a broad-spectrum and efficient scale inhibitor/dispersant used for membrane fouling in reverse osmosis equipment. Reverse Osmosis Scale Inhibitor BT0110 is an efficient liquid reverse osmosis membrane scale inhibitor used to control scaling deposits in membrane separation systems and effectively control calcium carbonate, calcium silicate, and calcium sulfate scales. Its scale inhibition efficiency is high and it does not form insoluble polymers with residual organic coagulants. Prevent scaling in reverse osmosis (RO), nanofiltration (NF), or ultrafiltration (UF) systems without ion exchange pre-treatment, improve water production and quality, and reduce operating costs.

BITU high-efficiency and hard water reverse osmosis scale inhibitor BT0110 is suitable for membrane types: high-efficiency reverse osmosis scale inhibitor BT0110 is suitable for Dow. Filmtec, Hydranautics, Fluid Systems, TORAY, CSM, JOZZON, E-MEM, Vonton The scale inhibition and dispersion applications of various imported domestic membranes and systems, such as Keensen.

Product Features

(1) Can be used in combination with organic flocculants;

(2) Can be used for producing drinking water;

(3) Effectively control the scaling of calcium carbonate, calcium sulfate, barium sulfate, and strontium sulfate, with an L.S.I value of up to 3.0 without causing scaling;

(4) All major reverse osmosis membranes can be used;

(5) Maintaining a clean reverse osmosis membrane surface by dispersing blocked particles;

(6) The influent pH is effective within the range of 5-9;

(7) It can be added directly without dilution, or after dilution;

(8) Good resistance to aluminum and iron oxides.

Technical indicators:

Appearance: Light yellow transparent liquid

PH value (1% aqueous solution): 2.5 ± 1.0

Density (20 ℃) g/cm ³： 1.10±0.05

Usage requirements

Dosing: The high hardness reverse osmosis scale inhibitor BT0110 product is continuously added to the inlet water before entering the membrane system. The typical dosage is 3-5 mg/l, which varies depending on the chemical properties of the water, membrane type, and system operating parameters (such as recovery rate, temperature, and pressure). The specific dosage will be calculated by the service provider.

Dilution: The high hardness reverse osmosis scale inhibitor BT0110 product should be continuously added. It is recommended to dilute it with RO produced water or desalinated water, with a dilution ratio not exceeding 10.

Note: Excessive or insufficient dosage can cause membrane fouling.

Packaging and Storage

Packed in plastic barrels with a net weight of 25 kilograms per barrel; Shelf life: Store in a dark and cool place, valid for 2 years.

Safety and Protection

Wear latex gloves, protective glasses, and protective clothing. If it splashes into the eyes, immediately rinse them with plenty of water and seek medical attention promptly. Prevent spillage on the cement floor to prevent corrosion. If it erodes the floor, please immediately rinse with clean water.

High hardness and high calcium water quality reverse osmosis scale inhibitors can be formulated according to technical requirements. Here, reverse osmosis scale inhibitors used in various water quality environments such as high sulfate water quality, high hardness water quality, high alkali water quality, high iron water quality, high aluminum water quality, high silicon water quality, high turbidity water quality, high COD water quality, etc. can be customized and processed to meet the needs of users in various industries. Jiaming Water Treatment Technology (Shanghai) Co., Ltd. is composed of dozens of well-known experts and technologies with over 20 years of experience in the water treatment chemicals and equipment industry. With strong technical strength and rich application experience, Jiaming is a well-known brand of reverse osmosis scale inhibitors.